Announcement

Collapse
No announcement yet.

Todd's new S2000

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Originally posted by Toddxxx View Post
    https://trackbuilt.wordpress.com/201...ring-cleaning/

    New blog update on my recent bits and bobs

    Sent from my VTR-L09 using Tapatalk
    How did you prep your VC for paint? I'm planning on doing the VC gasket, cam seal and spark plug tube seals in a few weeks when i'm free and i'm thinking of painting the VC at the same time while it's off.

    Comment


      Originally posted by Kingk22 View Post
      How did you prep your VC for paint? I'm planning on doing the VC gasket, cam seal and spark plug tube seals in a few weeks when i'm free and i'm thinking of painting the VC at the same time while it's off.
      First I removed all the grommets and Seals etc and taped up the holes that went into the inside of the valve cover and then stripped all the old paint off. Took a few goes with the brush, tooth brush and scraper to get every last bit. Gave it a good high pressure hose wash to clean out everything then let it dry overnight.
      Cleaned it up with wax and grease remover and gave a few spots a little sand with 1200 grit sand paper. Cleaned with wax and grease remover again making sure to get everything. Masked up all the surfaces I didn't want painted then used vht wrinkle black and instead of doing the usual 3 thick coats I did 5 lighter ones for a smaller more subtle wrinkle.Let it cure in the sun for a couple hours then remove the tape areas and clean them up using nail polish remover and a cotton bud.
      Then I bunged it in the oven for a couple mins each either side.

      Sent from my VTR-L09 using Tapatalk
      Last edited by Toddxxx; 15-12-17, 10:01 PM.

      Comment


        Some questions:

        1. Did you have to do it with the oven door open?

        2. Did you get busted for using the oven to bake the cover?

        3. Obviously you’re still alive...but how bad are the injuries?

        ...just wanted to know before I try the same

        Comment


          Originally posted by Apu View Post
          Some questions:

          1. Did you have to do it with the oven door open?

          2. Did you get busted for using the oven to bake the cover?

          3. Obviously you’re still alive...but how bad are the injuries?

          ...just wanted to know before I try the same
          1. You're actually meant to close the oven and bake it for an hour. It didn't fit in my oven so I just grilled it for 5mins each half haha

          2. I did it at my parents place when they weren't home. No trouble that way [emoji14]
          I'm not silly enough to do it in my own place hahaha

          3. Read above

          Sent from my VTR-L09 using Tapatalk

          Comment


            Interested to hear your impressions of the RE71R. Internet lore suggests they're even more cheater than the Rival S I'd been using.

            Comment


              Originally posted by ChargeR View Post
              Interested to hear your impressions of the RE71R. Internet lore suggests they're even more cheater than the Rival S I'd been using.
              Yeah going by online talk the rival S is the closest competitor to the re71r. It'll be interesting to see where they fall between the rs3 and A050 in terms of lap times. Just going to wait for the new year then head out

              Sent from my VTR-L09 using Tapatalk

              Comment


                Is putting it in the oven necessary, even on non-wrinkle-finish paint?

                Comment


                  Originally posted by Kingk22 View Post
                  Is putting it in the oven necessary, even on non-wrinkle-finish paint?
                  You don't 'have' to, but the general consensus is it helps with the wrinkle finish.

                  Originally posted by Toddxxx View Post
                  Lmao that poor oven mitt

                  Comment


                    Yeah you don't have to do it. The wrinkle still comes through just drying it. I did it on a sunny day and left it in the sun to help it get warm and dry out. The baking in the oven makes the wrinkle more pronounced and because I wanted a subtle finish the non baking method worked well.

                    Sent from my VTR-L09 using Tapatalk

                    Comment


                      Got my rims back from powder coating yesterday. Went with silver brilliance colour which is very similar to Ti silver. They came out great! Pass did a good job. I have brand new volk racing decals to go on the spokes as well as new black rays valves.
                      My RE71R are getting sent to me next week and hopefully get them mounted on the rims and back on the car before Xmas.

                      Car is currently in pieces with stuff pulled off everywhere. Have about 10 different jobs going at once.

                      Plan is to get out to the first smsp practice of the year on the 25th Jan. Before then the main jobs that need to be done are:

                      - tyres mounted, balanced etc and put back on car

                      - alignment

                      - finish stage 2 of my weight reduction program

                      - get new battery installed and wired in

                      - full spanner check

                      - change front rotors


                      Sent from my VTR-L09 using Tapatalk
                      Last edited by Toddxxx; 15-12-17, 10:02 PM.

                      Comment


                        Post one of two for today done.
                        Will write the next one up on my break.

                        https://trackbuilt.wordpress.com/201...to-me-from-me/



                        Sent from my VTR-L09 using Tapatalk
                        Last edited by Toddxxx; 22-12-17, 04:42 PM.

                        Comment


                          Post two of two is up.
                          Enjoy

                          https://trackbuilt.wordpress.com/2017/12/22/re71-r/

                          Sent from my VTR-L09 using Tapatalk
                          Last edited by Toddxxx; 29-12-17, 01:24 PM.

                          Comment


                            Hmmm...needs carbon doors

                            Comment


                              Originally posted by Apu View Post
                              Hmmm...needs carbon doors
                              No carbon doors unless I have a cage with side intrusion bars etc

                              Sent from my VTR-L09 using Tapatalk

                              Comment


                                Needs roll cage with door bars

                                Comment

                                Working...
                                X